CompactPCI * CPU Mezzanine
C23-1-SATA	3U/4HP Mezzanine expansion side board for CCD-CALYPSO - CCG-RUMBA - CCM-BOOGIE, 3 x COM, PCIe to 2 x SATA / 1 x PATA controller, SIO, FWH, USB, USB SSD, option AC'97 Codec(CCD only), option TPM
CompactPCI * Adapter
CA1-1-FUSION	6U, adapter PCI-to-CompactPCI, for short PCI boards (max. 107mm x 168 mm), horizontal or vertical installing of PCI board, 8HP front panel for proper mounting
CA2-1-FUNK	3U, adapter PCI-to-CPCI (carrier/bridge), 1 PCI slot suitable for PCI Card 57.00mm x 160.00mm, front panel width 8HP
CA2-2-FUNK	3U, adapter PCI-to-CPCI (carrier/bridge), 3 PCI slots suitable for PCI Short Cards, front panel width 4HP (open frame mounting of the PCI Cards)
CA2-3-FUNK	3U, adapter PCI-to-CPCI (carrier/bridge), 3 PCI slots suitable for PCI Short Cards, front panel width 28HP (completely covering the PCI Cards)
CompactPCI * USB
CB2-1-PIPE	3U, 5-port USB2.0 480Mbps host adapter EHCI/OHCI
CompactPCI * CPU Low Power
CC9-2R-SAMBA	3U/4HP ULV Celeron M 1.0GHz CPU Dothan 373 (TDP 5W), 512MB DDR, DVI-I video, Gigabit Ethernet, USB2.0, ATA CompactFlash slot, suitable for rear I/O across J2
CC9-3R-SAMBA	Similar to CC9-2R-SAMBA, but LV Pentium M 1.4GHz CPU Dothan 738 (TDP 10W)
CC9-AR-SAMBA	Similar to CC9-2R-SAMBA but ULV Celeron M 600MHz CPU (TDP 7W)
CompactPCI * CPU Mezzanine
CCA-1-LAMBADA	3U/4HP Mezzanine expansion board for CC9-SAMBA, AC'97 audio in/out, RS-232 (COM), USB, PS/2 KB/MS, option on-board hard disk
CCB-1-BOSSANOVA	3U/4HP Mezzanine expansion board for CC9-SAMBA, 100Mbit Ethernet, 2 x USB, 1 x RS-232 COM port, PS/2 KB/MS, option on-board hard disk
CCB-2-BOSSANOVA	3U/4HP Mezzanine expansion board for CC9-SAMBA, 100Mbit Ethernet, 2 x RS-232 COM port, PS/2 KB/MS option on-board hard disk
CompactPCI * CPU General Purpose
CCD-2R-CALYPSO	3U/4HP ULV Celeron M 373 1.0GHz CPU, FSB 400MHz, DVI-I video, 2 x GB Ethernet, 7 x USB2.0, 3 x SATA, PATA, CompactFlash slot, 2 x 512MB DDR2 (533), suitable for rear I/O across J2
CCD-3R-CALYPSO	Similar to CCD-2R-CALYPSO, but LV Pentium M 738 1.4GHz CPU
CCD-6R-CALYPSO	Similar to CCD-2R-CALYPSO, but SV Pentium M 760 2.0GHz CPU FSB 533MHz
CompactPCI * CPU Mezzanine
CCE-1-PUNK	3U/4HP Mezzanine expansion board for CCD-CALYPSO, 2 x 1394a FireWire, 2 x USB2.0, 2 x RS-232, option on-board hard disk
CCE-2-PUNK	Similar to CCE-1-PUNK, w/o IEEE 1394
CompactPCI * CPU Dual Core
CCG-1RD-RUMBA	3U/4HP, Core(TM) 2 Duo U7500 1.06GHz FSB 533MHz 2MB L2, dual socket DDR2 SO-DIMM up to 4GB, DVI-I dual screen, dual GB-ETH, 7 x USB, 1 x PATA, 3 x SATA-2, 4 x PCIe, CF card slot, suitable for rear I/O across J2
CCG-4RD-RUMBA	Similar to CCG-1RD-RUMBA, but Core(TM) 2 Duo L7500 1.6GHz CPU, FSB 800MHz, 4MB L2
CCG-8RD-RUMBA	Similar to CCG-1RD-RUMBA, but Core(TM) 2 Duo T7500 2.2GHz CPU, FSB 800MHz, 4MB L2
CompactPCI * CPU Mezzanine
CCH-1-MARIACHI	3U/4HP Mezzanine expansion board for CCG-RUMBA, HD audio codec (Azalia), option TPM 1.2, DVI-D digital video, analog audio, RS-232 (COM), option on-board hard disk
CCH-2-MARIACHI	Similar to CCH-1-MARIACHI, 2 x RS-232 (COM), w/o DVI video
CCH-3-MARIACHI	Similar to CCH-1-MARIACHI, DVI video, digital audio, w/o RS-232 (COM)
CCH-4-MARIACHI	Similar to CCH-1-MARIACHI, 1 x RS-232 (COM), digital audio, w/o DVI video
CCI-1-RAP	3U/4HP Mezzanine expansion board for CCG-RUMBA and CCM-BOOGIE, side board with PCI Express Mini Card sockets
CCJ-1-RHYTHM	3U/4HP Mezzanine expansion board for CCG-RUMBA, System Slot sideboard for CompactPCI Express, DVI-D, 1 x USB, 2 x FireWire, 1 x RS-232 (COM), on-board hard disk option, option TPM 1.2
CCJ-2-RHYTHM	Similar to CCJ-1-RHYTHM, 2 x RS-232 (COM), w/o DVI video
CCK-1-MARIMBA	3U/4HP Mezzanine expansion board for CCG-RUMBA and CCM-BOOGIE, side board with PMC/XMC module socket
CCL-1-CAPELLA	3U/4HP Mezzanine expansion board for CCG-RUMBA and CCM-BOOGIE, side board with 4 x GB-Ethernet
CompactPCI * CPU Dual Core Hi Per
CCM-2RD-BOOGIE	3U/4HP, Core(TM) 2 Duo ULV 1.2GHz, FSB 800MHz, 3MB L2, TDP 10W, GS45 graphics, dual channel DDR3 up to 8GB, DVI-I dual screen, dual GB-ETH, 3 x SATA-2, PCIe x 4, suitable for rear I/O across J2
CCM-4RD-BOOGIE	Similar to CCM-2RD-BOOGIE, Core(TM) 2 Duo LV 1.86GHz CPU, FSB 1066MHz, 6MB L2
CCM-6RD-BOOGIE	Similar to CCM-2RD-BOOGIE, Core(TM) 2 Duo SV 2.26GHz CPU, FSB 1066MHz, 6MB L2
CompactPCI * CPU Rear I/O
CCR-1-RIO	3U/4HP Rear I/O transition module for CC9-SAMBA, VGA, IDE (40/44-lead headers), 2 x USB, PS/2 KB/MS, RS-232, GB-Ethernet
CCT-1-RIO	3U/4HP Rear I/O transition module for CCD-CALYPSO - CCG-RUMBA - CCM-BOOGIE, 2 x SATA, 1 x ESATA, 2 x USB, GB-Ethernet, VGA video, RS-232
CCY-1-RIO	3U/4HP Rear I/O transition module for CC2-TANGO and CC3-CAJUN, PATA, USB, PS/2 KB/MS, RS-232
CompactPCI * CPU 6U Gen Purpose
CD3-3-JIVE	6U, LV Pentium M 1.4GHz (Dothan 738), 1GB DDR2, 3 x GB-Ethernet, PICMG 2.16 Dual Link, 8 x USB, 4 x SATA, CompactFlash ATA slot, 1 x PMC mezzanine, dual screen video, rear I/O
CD3-6-JIVE	Similar to CD3-3-JIVE but 2.0GHz Pentium M 760 (533MHz FSB)
CompactPCI * CPU 6U Rear I/O
CDT-1-RIO	6U/4HP Rear I/O transition module (J3/J4/J5) for CD3-JIVE
CompactPCI * SATA/IDE
CE5-1-CADENZA	3U, Quad Serial ATA controller (SATA RAID option), 4 front panel SATA connectors
CE5-1H-CADENZA	3U, Quad Serial ATA controller (SATA RAID option), 3 front panel SATA connectors, 1 SATA/IDE-Bridge with connector for internal usage, with 2.5-inch on-board IDE hard disk drive
CE5-2-CADENZA	3U, Quad Serial ATA controller (SATA RAID option), 4 on-board SATA connectors for internal usage
CE5-2H-CADENZA	3U, Quad Serial ATA controller (SATA RAID option), 3 on-board SATA connectors for internal usage, 1 SATA/IDE-Bridge with connector for internal usage, with 2.5-inch on-board IDE hard disk drive
CompactPCI * IEEE 1394 FireWire
CF2-2-CYMBAL	3U, 3-Port 400Mbps IEEE 1394 FireWire OHCI hostadapter, High Performance Serial Bus, TI OHCI-Lynx LLC, TI triple cable PHY 400Mbps
CompactPCI * GPS Receiver
CG2-1-SHANTY	3U, GPS 12-channel receiver (position, clock), NMEA-0183 & SiRF binary protocol, DGPS input RTCM SC-104 protocol
CompactPCI * ISDN
CI1-1-HARP	3U, ISDN S/T (S0) terminal adapter, Windows drivers/CAPI W98/NT4 (by download from EKF website)
CompactPCI * Networking
CN4-1-BELL	3U, quad 10BASE-T/100BASE-TX Fast Ethernet NIC, auto-negotiation, full-duplex, 4 x RJ45
CN6-1-ECHO	3U, Dual 1000BASE-T Gigabit Ethernet NIC, 2 x RJ45 10/100/1000Mbps, 32/64-bit J1/J2 CPCI 33/66MHz
CompactPCI * PC Card / CardBus
CP3-1-HOUSE	3U, Dual socket PC Card hostadapter, 2 type I-II cards or 1 type III PC Card, compliance (mix and match) with 16-bit PCMCIA and 32-bit CardBus cards
CompactPCI * ExpressCard
CP5-01-GLAM	3U, new technologies carrier board: one ExpressCard slot 34/54mm, two PCI Express MiniCard sockets incl. SIM/UIM card holders, 2 x SMA antenna connectors for WiFi/GSM/WiMax, 2 x USB Flash module (SSD) sockets
CP5-02-GLAM	3U, new technologies carrier board: Single ExpressCard slot 34/54mm, full support for PCI Express & USB type ExpressCards
CP5-11-GLAM	3U, new technologies carrier board: two PCI Express MiniCard sockets incl. SIM/UIM card holders, 6 x SMA antenna connectors for MIMO WiFi/GSM/WiMax, 2 x USB Flash module (SSD) sockets
CompactPCI * System Rack
CR1-1-RACK	19-" system rack 1U, 2 slot CompactPCI backplane 6U, P1-P5 (P3-P5 rear I/O), power supply 100-240VAC 200W
CR4-1-RACK	19" System rack 4U, 8-slot CompactPCI backplane 3U P1-P2, removable power supply, floppy disk, hard disk, DVD-ROM, 1U fan unit, depth 280mm, suitable for 3U CompactPCI boards
CR4-2-RACK	19" System rack 4U, 8-slot CompactPCI backplane 3U P1-P2, industrial ATX power supply, 1U fan unit, depth 280mm, suitable for 3U CompactPCI boards
CR4-3-RACK	Similar to CR4-1-RACK, P1/P2 rear I/O backplane,
CR4-9-RACK	Option 4U desktop case
CR7-1-RACK	19" System rack 7U, 6U 8-slot CompactPCI backplane 6U P1-P5 (rear I/O), power supply, floppy disk, hard disk, DVD-ROM, 1U fan unit, depth 280mm, suitable for 6U rear I/O CPCI boards
CR9-5-ADAPT	front panel expansion adapter for 3U board mounting in 6U racks, suitable for all EKF 3U (4HP) boards, mounting kit includes all required parts
CR9-6-ADAPT	same as CR9-5, but double width (8HP)
CRB-1-BLUELINE	'Blue Line' 3U/30HP small system rack, w h d ~ 172mm x 132mm x 208mm, incl. tip up feets CPCI PSU 70W 115/230VAC, CPCI backplane 4 x P1, suitable for 3U CompactPCI boards
CRB-2-BLUELINE	Similar to CRB-1-BLUELINE, 24VDC power line input
CRB-4-BLUELINE	'Blue Line' 3U/30HP small system rack incl. fan unit, w h d ~ 172mm x 166mm x 208mm, incl. tip up feets, CPCI PSU 70W 115/230VAC, CPCI backplane 4 x P1, suitable for 3U CompactPCI boards
CRB-5-BLUELINE	Similar to CRB-4-BLUELINE, 24VDC power line input
CompactPCI * Wide Ultra2 SCSI
CS3-1-FLUTE	3U, SCSI hostadapter, 80MByte/s, LVD and single-ended, syn/async, SCSI-1/2, Fast/Ultra/Ultra2 SCSI, PnP, SCAM, ISP Flash BIOS, 53C895 controller, auto termination, bootable, 68-pole (ext) and 68-pole (int) connectors
CompactPCI * Ultra160 SCSI
CS5-1-HORN	3U, dual SCSI HA, 2x160MB/s Ultra160 LVD/SE, dual external VHDCI receptacles, single internal HDSUB connector, auto termination, 53C1010-33 controller, Flash BIOS, bootable, 33MHz 32-bit CPCI I/F J1
CS5-2-HORN	Similar to CS5-1-HORN, 53C1010-66 controller, 66MHz 32/64-bit CPCI I/F J1/J2
CompactPCI * Serial Interface
CU4-1-SOPRANO	3U, 4-port asynchronous serial interface, RS-232/RS-485 individually selectable, front panel I/O, w/o J2 connector, suitable for 32/64-bit CPCI backplane
CU4-1P-SOPRANO	3U, 4-port asynchronous serial interface, RS-232/RS-485 individually selectable, front panel I/O, w/o J2 connector, suitable for 32/64-bit CPCI backplane additional on board parallel port
CompactPCI * Parallel Interface
CU4-P-SOPRANO	3U, 1-port parallel interface, 25 pos. DSUB front panel
CompactPCI * Serial Interface
CU7-2-RS485	RS-485/RS-422 Rear I/O PHY interface module, 1 port, 2.5Mbps 4-wire transmission line (point-to-point), electrically isolated, including cabling assembly
CU8-1-RS232	RS-232E/V.28 Rear I/O PHY interface module, 1 port, full modem support, ESD protection, max. 230 kbps, includes 30cm metric flat ribbon cable assembly, not included: rear mounting panel
CU9-4-BASE	3U Transition adapter board, bridge between CU4-SOPRANO rear I/O (backplane J2) and CU7/CU8 PHY interface modules, 4 ports (2mm connectors), 3U back panel 8HP
Software * Microsoft
CZ-00-XPE-003	Windows XP Embedded for Point of Services SP2 licence, WEPOS, English only available with EKF boards/systems
CZ-00-XPE-004	Windows XP Embedded SP2 licence, English, incl. driver for graphics and networking, only available with EKF boards/systems
CZ-00-XPE-005	Tool Target Designer, English, generates Windows XP Embedded SP2 images
CZ-00-XPW-005	Windows XP Professional SP3/OEM, English, incl. driver for graphics and networking, only available with EKF boards/systems
CZ-00-XPW-005D	Windows XP Professional SP3/OEM, German, incl. driver for graphics and networking, only available with EKF boards/systems
Software * Linux
CZ-95-LINUX-003	Linux SuSE Professional
CZ-95-LINUX-004	Sysgo Embedded Linux